Ted392 Mods

[Electrified]

Received my Clayton coils this week, for those of you who have them, mine say 2.5” JL/JK for front and 1.5” JL for rear, nothing specific to 392. Can you confirm yours were the same?

I would call Clayton and have them confirm you have the right springs for your 392.

 

[Jgc650i]

Received my Clayton coils this week, for those of you who have them, mine say 2.5” JL/JK for front and 1.5” JL for rear, nothing specific to 392. Can you confirm yours were the same?

Yes, that’s what mine were as well.

 

[@WhiteBronze392]

I don't recall what the boxes stated, I ordered the 392 coils. I do know only the rears springs are stamped Left and Right.

I got lucky with the rear I didn’t realize there were left and right didn’t even pay attention and somehow managed to get them correct.

 

[Ted392]

6,000 miles and counting.
3rd oil change, 2nd 5 tire rotation. Trails tomorrow!

 

[@WhiteBronze392]

6,000 miles and counting.
3rd oil change, 2nd 5 tire rotation. Trails tomorrow!

I’m thinking about heading back over to where the “group trip” was last weekend again Sunday solo.

 

[Ted392]

Fun and dusty. Love the ride and the engine! So much for the exterior cleaning!

Engineering sand box and hill climb area for LMTV's, etc. Lots of sand!

 

[@WhiteBronze392]

Awesome man! The ride is more fun with half doors but not the cleanup

 

[Ted392]

Awesome man! The ride is more fun with half doors but not the cleanup

The dust pain is real!

 

[Ted392]

After off roading last weekend, I had my detailing friend install ceramic coating over the ppf.

6750 miles

In 6 weeks, Ouray CO trip!

 

[@WhiteBronze392]

The Fox ATS steering stabilizer can be mounted in the oem position. Or, it can be mounted on the axle side track bar bolt and then clamped to the tie rod. This position raises it up high and less prone for rock strikes.

Did you ever end up doing this? looking into brackets/clamps

 

[Ted392]

Did you ever end up doing this? looking into brackets/clamps

Partially. I installed the new track bar bolt but the shaft is almost the same as the hole in the ss. So I quite installing it. I have not had time to investigate it yet. Figured I'd do it over the 4th of July.

When I called the supplier, they shrugged me off. So if I can't get it to work, I'll buy someone else's product and post it.

Frustrating...

 

[@WhiteBronze392]

Partially. I installed the new track bar bolt but the shaft is almost the same as the hole in the ss. So I quite installing it. I have not had time to investigate it yet. Figured I'd do it over the 4th of July.

When I called the supplier, they shrugged me off. So if I can't get it to work, I'll buy someone else's product and post it.

Frustrating...

I ordered the Synergy kit today. I cant remember are you using Fox ATS?

 

[Ted392]

I ordered the Synergy kit today. I cant remember are you using Fox ATS?

Yes Fox ATS

 

[@WhiteBronze392]

Yes Fox ATS

Was it also Synergy? I read a post today about lightly sanding the bolt with sandpaper and the Fox ATS slipped right on but that was the only case I found where anyone had trouble

 

[Ted392]

Was it also Synergy? I read a post today about lightly sanding the bolt with sandpaper and the Fox ATS slipped right on but that was the only case I found where anyone had trouble

I think so. I'll look tonight and report back. Thanks for the info, it was what I was gonna do to see if it fits.

 

[Ted392]

I relocated ATS ss successfully.

Synergy
syn8806-01 JL stud
Syn4050-63 JL tie rod clamp
Syn 4051-01 fox ats clamp adapter washer.

 

[Ted392]

Primed and painted the muffle and tips hi temp black.
Now I'll be able to see the rock rash

 

[27X510JL]

I don't recall what the boxes stated, I ordered the 392 coils. I do know only the rears springs are stamped Left and Right.

I recently installed the Clayton 392 performance springs and mine had the same stamp. Installed and leveled the Jeep out. Rides great on road

 

[@WhiteBronze392]

I relocated ATS ss successfully. View attachment 23164
View attachment 23165
View attachment 23166

Synergy
syn8806-01 JL stud
Syn4050-63 JL tie rod clamp
Syn 4051-01 fox ats clamp adapter washer.

Looks so much better and out of the way!

 

[Tank2112]

I relocated ATS ss successfully. View attachment 23164
View attachment 23165
View attachment 23166

Synergy
syn8806-01 JL stud
Syn4050-63 JL tie rod clamp
Syn 4051-01 fox ats clamp adapter washer.

Some have stated issues with clamp, that bolts around drag link, sliding/moving. Why not use three, add one to each side of the one actually securing stabilizer shock?