Steering Stabilizer Dilemma…

Finished the install of the Teraflex stabilizer today. There is a definite difference between the three settings (soft, medium, hard). The medium is where I am now, but the hard didn't seem too bad either (except when making a very sharp turn). Total install time was 2 hours, mainly because one of the factory bolts you are supposed to re-use would not fit through the hole in the Teraflex, so I had to go buy a new carriage bolt.

Honestly, I'm still torn if it made a $400 difference in the steering. It feels different, even driving straight... so maybe I just need to get used to it. LOL
 
Finished the install of the Teraflex stabilizer today. There is a definite difference between the three settings (soft, medium, hard). The medium is where I am now, but the hard didn't seem too bad either (except when making a very sharp turn). Total install time was 2 hours, mainly because one of the factory bolts you are supposed to re-use would not fit through the hole in the Teraflex, so I had to go buy a new carriage bolt.

Honestly, I'm still torn if it made a $400 difference in the steering. It feels different, even driving straight... so maybe I just need to get used to it. LOL
Thanks for the feedback. I have a Fox ATS sitting in the garage for two weeks now…need to make the time. I suspect I’ll be in the same boat - difference? Probably a little but most likely not $400 worth. Glad I have the correct/old bolt on hand 👍
 
Would the Fox ATS help correct a steering pull? Are there adjustments for this? After I installed 35 MTs, I’m getting a slight pull to the right. Not too bad, but just enough that I can notice. Would rather not deal with replacing tires, etc.
 
Would the Fox ATS help correct a steering pull? Are there adjustments for this? After I installed 35 MTs, I’m getting a slight pull to the right. Not too bad, but just enough that I can notice. Would rather not deal with replacing tires, etc.
Toe might need to be pulled in a little if the tire weight is too much for current setting. ATS are neutral, they don’t push or pull so won’t help if you’re getting a drag, they help to stop wobble and drift.
 
Toe might need to be pulled in a little if the tire weight is too much for current setting. ATS are neutral, they don’t push or pull so won’t help if you’re getting a drag, they help to stop wobble and drift.
Got it. I’ll start with the basics, rotate the tires, check the tire balance and maybe have the alignment checked.
 
Got it. I’ll start with the basics, rotate the tires, check the tire balance and maybe have the alignment checked.
All I did was swap the two front tires and now all is good! The drivers side wheel had less weight added for balancing, so perhaps the passenger wheel being heavier was enough to cause pulling?
 
I tried to install the Fox ATS on my 392 XR yesterday and it did not fit. The track bar is in the way - the stabilizer reservoir won’t clear it. The bracket didn’t line up very well either. Guess I’ll be selling it. Ugh
 
I tried to install the Fox ATS on my 392 XR yesterday and it did not fit. The track bar is in the way - the stabilizer reservoir won’t clear it. The bracket didn’t line up very well either. Guess I’ll be selling it. Ugh
I might be mistaken, but isn’t there a company that makes a “reversed” bracket?
 
I tried to install the Fox ATS on my 392 XR yesterday and it did not fit. The track bar is in the way - the stabilizer reservoir won’t clear it. The bracket didn’t line up very well either. Guess I’ll be selling it. Ugh
It fit on mine, installer said not to tighten anything down until all bolts were in because it was a little tight.
 

Attachments

  • DAFD1038-9F1C-40A3-8709-D5EE5446C0AC.webp
    DAFD1038-9F1C-40A3-8709-D5EE5446C0AC.webp
    167.6 KB · Views: 224
  • F98D3C62-3A41-48F0-9771-6F320BAE3219.webp
    F98D3C62-3A41-48F0-9771-6F320BAE3219.webp
    155.2 KB · Views: 223
It fit on mine, installer said not to tighten anything down until all bolts were in because it was a little tight.
It looks like you have a non XR…not sure if the track bar angle is slightly different? Even with the reservoir rotated back like that I don’t think mine would clear.
 
It looks like you have a non XR…not sure if the track bar angle is slightly different? Even with the reservoir rotated back like that I don’t think mine would clear.
It is a nonXR. I should have clarified that
 
@BenLandry i see from your pict you oriented the reservoir straight up. I just installed mine and I rolled it back towards the axle. Straight up looks like it will hit the track bar when stuffed? I moved the wheels back and forth and had no contact. should I rotate it?
 
@BenLandry i see from your pict you oriented the reservoir straight up. I just installed mine and I rolled it back towards the axle. Straight up looks like it will hit the track bar when stuffed? I moved the wheels back and forth and had no contact. should I rotate it?
Mine hasn’t hit yet, I have not fully flexed it though
 
I might be mistaken, but isn’t there a company that makes a “reversed” bracket?
I thought I heard you can order the JK bracket and that fixes the problem?? I could be wrong tho. LOL
 
I thought I heard you can order the JK bracket and that fixes the problem?? I could be wrong tho. LOL
That is if you don’t want to mount it in the stock location. The JK version comes with the right size clamp for tie rod mounting. I’m going to run it in the stock location for a bit.
 
That is if you don’t want to mount it in the stock location. The JK version comes with the right size clamp for tie rod mounting. I’m going to run it in the stock location for a bit.
Do you know of the part number/link for this bracket? I'm worried when mine gets installed the installer will want this
 
I tried to install the Fox ATS on my 392 XR yesterday and it did not fit. The track bar is in the way - the stabilizer reservoir won’t clear it. The bracket didn’t line up very well either. Guess I’ll be selling it. Ugh
Did you ever figure out a solution? Or did you end up selling it?
 
Did you ever figure out a solution? Or did you end up selling it?
Got rid of it and will be installing the adjustable Teraflex Falcon stabilizer this weekend. I’ve read some good reviews and I like that it only has three adjustments vs the Fox 20-something adjustment clicks.
 

Create an account or login to comment

Join now to leave a comment enjoy browsing the site ad-free!

Create account

Create an account on our community. It's easy!

Log in

Already have an account? Log in here.

Back
Top